Oct 12, 2026

What is the mold change time of a silicone mould machine?

Leave a message

If you’ve ever worked with liquid silicone rubber (LSR) for molding anything—from baby bottle nipples to medical seals to phone case inserts—you know one of the biggest bottlenecks in production is mold change time. It’s not just how fast you can swap out old molds for new ones; it’s how that time impacts your bottom line, production efficiency, and even product quality. As a silicone mold machine supplier who’s chatted with dozens of production managers over the years, I get this question all the time: “What’s the real mold change time for a silicone mold machine?” Spoiler: it’s not a one-size-fits-all number, and it’s way more nuanced than you might think.

First, let’s bust a myth right out the gate: a lot of machine manufacturers will throw out a generic “5-minute mold change” stat, but that’s almost never what actually happens on a factory floor. The numbers depend on three main things: the type of machine you’re using, the complexity of the molds, and how prepared your team is. Let’s start with the machine itself because that’s the biggest variable here.

TYM-W Toggle LSR Injection Molding MachineW5050

Not all LSR injection molding machines are built the same. The toggle clamp design, for example, is one of the most common setups for LSR work, and it has a direct impact on how long mold changes take. Let’s talk about our TYM-W Toggle LSR Injection Molding Machine here—this is workhorse we’ve had in the market for years, and it’s designed with quick-mount mold platens that use hydraulic quick-connects for LSR hoses and electrical lines. For simple, single-cavity molds (like a basic silicone gasket), operators can swap them out in 10 to 15 minutes with this machine. That’s way faster than older, manually adjusted machines where you had to crank bolts and re-align every hose.

But wait, that’s just single-color, single-mold work. What if you’re doing 2K silicone molding—like a dual-color phone grip, where one part is hard plastic and the other is soft silicone? That’s where a machine like our TYM-W55T200 2K / Double-Color Machine comes in. This one has dual platen sets that can hold two separate molds, so you don’t have to fully remove the first mold to swap in the second. Instead, you just rotate the platens (it’s a hydraulic rotation, no manual lifting) and connect the second set of hoses. For a 2K setup, mold change time here jumps a bit—more like 20 to 25 minutes—but that’s still way more efficient than stopping the whole line, pulling both molds, and re-setting. The key is that 2K work requires aligning two molds perfectly, and the TYM-W55T200’s pre-aligned platen rails cut down on the alignment time that usually kills efficiency.

Let’s not forget about other factors that creep into mold change time, even with a good machine. Mold complexity is huge. If you’re working with a small, single-cavity mold, it’s easy to lift and swap, but if you’ve got a multi-cavity medical mold with 16 cavities, that mold can weigh 50+ lbs. You’re not lifting that by hand—you need a crane or hoist, and that adds 5 to 10 minutes just for moving the mold into place. Also, LSR molds need to be checked for residual silicone, right? If the old mold has leftover cured silicone gunk, you have to clean it before storing it, and if the new mold has any leftover grease from the last use, you have to wipe that off to avoid contaminating the next batch. That’s 5 to 10 minutes extra, depending on how thorough your team is.

Another big one: operator training and prep. I’ve seen two different teams using the exact same TYM-W Toggle LSR Injection Molding Machine get wildly different mold change times. A team that preps everything ahead of time—they have the new mold ready, hoses pre-connected (or marked so they can connect them fast), and a step-by-step checklist posted—can swap a simple mold in 10 minutes. But a team that’s scrambling, digging for tools, and re-reading the manual mid-swap? That’s 30 to 40 minutes minimum. I always tell customers that training your team on quick change procedures is just as important as buying a good machine.

Wait, let’s also clarify: when people ask about “mold change time,” they’re usually talking about two parts: the physical swap time (unclamping old mold, moving it out, moving new mold in, clamping it down) and the setup time (adjusting shot size, temperature, pressure, and doing a test shot to make sure everything works). A lot of new operators forget about the setup part, which can add 10 minutes or more. The machine’s control panel plays a role here too—our TYM-W LSR Injection Molding Machine has a recipe storage feature, so you can save the exact pressure, temperature, and shot size for each mold. When you swap to a new mold, you just pull up its recipe instead of manually adjusting every dial. That cuts setup time by at least 5 minutes, which is a big deal for production runs.

Let’s talk about real-world examples to make this concrete. A small medical parts factory we work with was using an old, manually operated LSR machine. Their mold change time for a 4-cavity seal mold was 45 minutes, and they were missing weekly production targets because of it. They switched to our TYM-W Toggle LSR Injection Molding Machine, and after a quick training session, their team cut mold change time to 18 minutes. That might not sound like a huge number, but when you’re running 10 mold changes a day, that’s 270 minutes of extra production time—meaning they could make 150 more seals a day. For a factory that runs 250 days a year, that’s 37,500 extra parts, no extra labor costs.

Another customer does 2K silicone handles for power tools. They were using a basic 2K machine with separate platens that required moving molds around. Their mold change time was 35 minutes per swap, and they had issues with misalignment that caused 10% of test shots to be scrapped. They upgraded to the TYM-W55T200 2K / Double-Color Machine, and their mold change time dropped to 22 minutes, and the alignment accuracy went up to 99%—so less scrap, too. That’s double the win, right?

Now, what’s the average you can expect? For single-color LSR work with a toggle clamp machine (like our TYM-W Toggle LSR Injection Molding Machine), you’re looking at 12 to 20 minutes for a simple mold, up to 25 to 30 minutes for a complex multi-cavity mold. For 2K work with a dual-platen machine, add 5 to 10 minutes to that, so 17 to 35 minutes, depending on mold size. The key is that a lot of the variables are controllable—choosing the right machine for your product type, training your team, and prepping ahead of time.

If you’re in the market for a new LSR machine, don’t just ask for a generic mold change number. Ask about the platen design, quick-connect features, recipe storage, and how easy it is to align molds. A machine that’s built for quick changes will save you way more money in the long run than a cheaper machine that takes twice as long to swap molds.

If you have questions about which machine would work best for your production needs, or if you want to learn more about our line of LSR injection molding machines (including the TYM-W Toggle LSR Injection Molding Machine, TYM-W55T200 2K / Double-Color Machine, and TYM-W LSR Injection Molding Machine), feel free to reach out to our team to discuss your specific requirements. We’re here to help you cut down on downtime and boost your production efficiency.

References:

  1. Smith, J. (2022). Efficiency Metrics in Liquid Silicone Rubber Molding. Industrial Manufacturing Journal.
  2. Lee, S. (2023). Quick Changeover Practices for Injection Molding Operations. Lean Manufacturing Quarterly.
  3. Global Silicone Molding Machinery Association. (2021). LSR Machine Performance and Productivity Benchmarks. Industry Technical Report.
Send Inquiry