Nov 04, 2026

What is the molding cycle time of a silicone machine?

Leave a message

If you’ve ever stepped into a factory that makes silicone parts—think phone cases, medical seals, silicone keyboard pads, or even baby bottle nipples—you’ve probably seen those big, clanking (but actually super precise) machines whirring away. The question that pops up all the time for people who are new to silicone manufacturing, or even small production teams looking to scale, is: how long does that whole molding cycle actually take? And why does it matter so much? As someone who’s been selling silicone molding machines (and chatting with manufacturers all day, every day) for the last 8 years, I’m here to break this down in plain, no-jargon terms, plus throw in a few examples of the machines we offer that kill on cycle time.

First off, let’s get the basics straight: a molding cycle for silicone is literally the full run of one part from start to finish on the machine. It’s not just how long the silicone sits inside the mold (that’s the cure time, a big chunk of it) but also all the steps before and after: opening the mold, ejecting the finished part, closing it back up, injecting the new silicone, and a little cool-down or prep before the next cycle starts. A lot of new buyers only focus on the cure time, but the other steps add up fast—like, if your cycle is 60 seconds total and cure is 30 seconds, you’re wasting half the machine’s time on small delays. That’s where a good silicone machine makes all the difference.

Now, let’s get into the numbers. The average molding cycle for standard liquid silicone rubber (LSR) parts, which is what most low-to-medium complexity parts use, runs between 20 and 90 seconds. Wait, that’s a huge range, right? Why such a big gap? Let’s break down what factors shift that number, because that’s the key here—your cycle time isn’t a random number; it’s tied directly to what you’re making, the machine you’re using, and even the grade of silicone you pick.

First, the biggest variable: part size and thickness. Silicone cures when it’s heated, right? So a thick part needs more time to heat all the way through and cross-link properly—think a 5mm thick medical seal vs. a 1mm thin phone case. The thick one might need 45-60 seconds just for cure, while the thin one could pull off cure in 10-15 seconds. Then you add in the other steps, and suddenly that thin part’s total cycle is 25 seconds, while the thick one is 75. It makes sense, but you have to match your machine’s capability to your part. If you’ve got a big, thick part and try to run it on a tiny, entry-level machine, you’ll end up with long, clunky cycles that kill your production rate.

Second, machine type. Not all silicone molding machines are created equal, and this is where our team’s products come in—we’ve spent years designing machines that cut down the non-cycle wait time, which is a massive bottleneck for a lot of factories. Let’s talk about some of our best-sellers first: the TYM-W LSR Injection Molding Machine is a horizontal LSR machine built for consistent, high-volume runs. It has a fast-clamp system that cuts down mold open/close time by almost 20% compared to older models. For example, if a standard machine takes 5 seconds to open/close the mold, this one does it in 4, which over 10,000 parts adds up to 10,000 saved seconds—like 2.7 hours of extra production time a week. Then there’s the TYM-W Toggle LSR Injection Molding Machine, which is perfect for parts that need a tighter clamp (no silicone flash leaking out, which is a huge quality issue). The toggle design here is super efficient, so even when you’re running a heavy clamp for thick parts, you don’t waste extra time on the clamp moving slowly.

W5050TYM-W Toggle LSR Injection Molding Machine

Another big one: 2K or double-color silicone parts. Those are parts that have two different silicone materials (or silicone plus plastic, like a silicone grip on a plastic tool handle) and need to be molded in two stages. The TYM-W55T200 2K / Double-Color Machine is built exactly for this, and its rotary mold system cuts down the switching time between the two molds. A lot of generic 2K machines take 10+ seconds to rotate the mold and align it, but this one does it in 5 seconds. That might not sound like much, but for small double-color parts, total cycle time can still stay under 60 seconds—whereas other machines might push it to 80 or 90. That’s a 30% faster cycle, which means you make way more parts in a day without sacrificing quality.

Wait, let’s talk about waste, too, because cycle time ties directly to that. If your machine is slow, or you have delays because of bad mold design, you’re either rushing the cure time (leading to parts that aren’t fully cured, which crack or leak) or leaving the silicone in the mold too long (wasting material, which adds up fast for high-volume runs). A lot of new manufacturers don’t realize that a tiny 2-second delay per cycle can turn into thousands of dollars in wasted silicone a month. That’s why investing in a machine that’s optimized for cycle time, instead of just the cheapest one on the market, pays off way more in the long run.

Another factor: mold design. Surprise, it’s not just the machine or the part. If your mold has complex cores, undercuts, or has to move parts around to eject, that adds time. A simple 2-cavity mold for thin, flat parts will have way faster cycle time than a 16-cavity mold for a part with 5 small holes. Working with a mold maker who specializes in silicone parts and knows how to design for fast cycles (like using air ejection instead of mechanical pins, which are slower) can cut cycle time by another 5-10 seconds, no machine upgrade needed.

Let’s throw in a real example to make this concrete. A client of ours makes silicone phone cases—thin, 3mm thick, no complex features. They were using an old, 10-year-old LSR machine that had a cycle time of 45 seconds per part, making 2 parts per mold, so 160 parts per hour. They switched to the TYM-W LSR Injection Molding Machine, and adjusted their mold to a 4-cavity design. Their cycle time dropped to 28 seconds, so now they make 8 parts per mold, which is 857 parts per hour. That’s a 5x increase in production rate, just from a machine swap and small mold tweak. They told us they paid for the new machine in 6 months from the extra parts they’re making—crazy, right?

Now, what about longer cycles? For example, a medical silicone part, like a sealing gasket for a pacemaker, which needs to be very thick (8mm) and 100% consistent. Their cycle time might be 70-90 seconds, because the cure time needs to be longer to make sure there’s no uncured silicone inside. But even here, a good machine helps: the TYM-W Toggle machine’s precise temperature control keeps the mold at a steady 180°C (the standard cure temp for most LSR), so you don’t have to add extra cure time to compensate for uneven heating. That cuts 5-10 seconds off their cycle, which adds up when you’re making 100,000 parts a month.

Wait, also let’s talk about shot size. Shot size is how much silicone you inject per cycle, and it’s tied to part size, obviously. If your machine has a shot size that’s too small for your part, you have to do multiple shots per cycle, which adds time. If it’s too big, you’re wasting material and the machine has to push more silicone, which slows down the injection step. All our machines, from the TYM-W horizontal line to the 2K double-color one, are built to match a wide range of shot sizes, so you don’t have to compromise.

One common mistake I see new buyers make is chasing the shortest possible cycle time at all costs. But you have to balance speed with quality. If you run a cycle that’s too short, your parts will have issues like surface bubbles, incomplete cure, or flash (extra silicone sticking to the part). Flash is a huge headache because it means you have to trim every part by hand, which adds labor time and can even damage the part. Our machines have precise clamp pressure control, so you can set exactly how much pressure you need to hold the mold closed—no more, no less. That lets you run as fast as possible without getting flash, which is the sweet spot for cycle time.

So, to wrap up the key points here: the molding cycle time for a silicone machine isn’t a one-size-fits-all number. It depends on part size/thickness, machine type, mold design, and even the grade of silicone you use. For standard small-to-medium LSR parts, you’re looking at 20-60 seconds, while thicker or high-precision parts run 60-90 seconds. The biggest way to optimize this is using a machine built for speed, with features like fast clamp systems, precise temperature control, and efficient ejection, which is exactly what our line of TYM-W machines brings to the table—whether you need a horizontal LSR machine, a toggle model for tight clamps, or a 2K double-color machine for multi-material parts.

If you’re shopping around for a new silicone machine, or you’re looking to upgrade your current setup to cut cycle time and boost production, don’t hesitate to reach out. We work with factories of all sizes, from small startups making phone accessories to large medical device manufacturers, and we can help you pick the right machine for your specific parts and goals. We also offer customization for mold layouts, shot sizes, and cycle optimization, so you don’t have to settle for a machine that’s not perfect for your needs.

Reference:

  1. Silicone Injection Molding: Cycle Time Optimization for High-Volume Production. 2022. Industrial Molding Technology Journal.
  2. Liquid Silicone Rubber (LSR) Processing Guidelines. 2021. Society of Plastics Engineers (SPE) Rubber Division.
  3. Toggle vs. Horizontal LSR Machine Performance Comparison. 2023. International Journal of Manufacturing Technology.
Send Inquiry