If you’ve ever worked with silicone molding, you know how frustrating it is to open a mold and pull out a part with weird inconsistencies—thin spots, uneven density, or even tiny bubbles that ruin its function. As a silicone molding machine supplier, I get asked all the time: “Why do these issues keep happening, even when I think I’m following the same steps?” A lot of the answer comes down to one thing you might not be paying as much attention to as you should: pressure.


Pressure isn’t just a number on your machine’s screen—it’s the silent force that shapes silicone from a gooey liquid into a solid, high-quality part. Too little, and you end up with parts that are flimsy or don’t fill the mold all the way. Too much, and you risk flash, wasted material, or even damage to the mold itself. Let’s break this down, how it actually impacts silicone product quality, and how the right machine can make all the difference.
First, let’s talk about the two main types of pressure you deal with in LSR (liquid silicone rubber) molding, since that’s what most of our customers work with. There’s injection pressure, which is the force pushing the silicone into the mold, and holding pressure, which is the force that keeps the silicone pressed against the mold walls while it cures. These two work together, and misadjusting either kills quality.
Take injection pressure, for example. When you inject liquid silicone into a mold, it has to flow through narrow gates and cavities. If your injection pressure is too low, the silicone might cool down (or even start curing early) before it fills every corner. That’s how you get thin sections in a part, or parts that don’t match the design at all. A lot of new operators crank up pressure thinking that’ll fix it, but too high here has its own problems. It can push air into the silicone, which gets trapped as bubbles in the final part—those tiny voids might not look like a big deal, but they weaken the part, especially if it’s used for things like medical seals or baby bottle nipples.
That’s where the holding pressure comes in. Once the mold is full, silicone continues to expand a tiny bit as it cures. If you don’t hold enough pressure here, gaps form in the center of thick parts, leading to uneven density. On the flip side, too much holding pressure can force excess silicone out of the mold’s vent gaps, creating flash—those thin, unwanted edges you have to trim off. Flash means wasted material, extra labor, and even parts that don’t fit correctly when assembled.
I’ve seen this play out a hundred times with our customers. One guy was making silicone phone cases and kept having flash issues that made him scrap 15% of his batches. He was using a generic machine with no precise pressure controls, so he couldn’t dial back the holding pressure enough without risking short shots. Once he switched to our TYM-W LSR Injection Molding Machine, he could adjust injection and holding pressure in small, repeatable increments. Flash dropped to less than 2%, and his yield jumped way up. That’s the thing about silicone molding—precision pressure control isn’t a luxury, it’s a necessity.
Wait, let’s clarify: not all pressure control is the same. Toggle machines vs. horizontal machines—there’s a real difference here. Our TYM-W Toggle LSR Injection Molding Machine, for example, uses a toggle clamping system that locks the mold evenly across its entire surface. That’s huge because if the clamp pressure is uneven, one side of the mold might open just a tiny bit, causing flash there while another side is too tight, leading to short shots. The toggle design ensures uniform pressure across the mold, so you don’t have to guess or compensate for uneven clamping.
Another example: double-color molding, which is when you combine two different silicone materials (or silicone and a rigid plastic) in one part. That’s trickier because you have to align pressure for both materials perfectly. Our TYM-W55T200 2K / Double-Color Machine is built for that. It has independent pressure controls for each injection unit, so you can adjust each material’s injection and holding pressure without messing up the other. A customer making medical device grips needed soft silicone for the grip and hard silicone for the core—if the pressure was off, the two layers would separate, or one would deform. With this machine, they got perfect bonding every time, and their defect rate went from 8% to almost zero.
Let’s dig into the science a little, because it’s not just guesswork here. Liquid silicone is a low-viscosity material, especially when it’s first injected. Its viscosity changes with pressure and temperature—higher pressure actually lowers viscosity a bit, which helps it flow better into tiny cavities. But that window is small. If you go above the optimal pressure, the viscosity drops too much, and the silicone flows too fast, trapping air instead of pushing it out through the mold vents. Those trapped air bubbles are what cause the “porosity” you see in low-quality silicone parts.
Temperature plays into this too—pressure and temperature work together. If your mold temperature is too low, you need higher injection pressure to get the silicone to fill, but that can lead to premature curing. A good machine doesn’t just control pressure; it syncs pressure with temperature so you get the best of both worlds. Our TYM-W models, for instance, have closed-loop pressure sensors that adjust in real-time if the temperature shifts, so you don’t have to stop the line to tweak settings every five minutes. That consistency is key for high-volume production, where even a 10-second pause for adjustment can cost you thousands in lost parts.
Another quality issue pressure causes is part uniformity. Silicone parts are often used for things like gaskets, O-rings, or seals, where density has to be exactly the same everywhere. If injection pressure varies cycle to cycle, the silicone doesn’t fill uniformly, leading to parts that are thicker in some spots and thinner in others. Thinner spots are more likely to tear, and thicker spots might not fit into their intended space. Precise pressure control means every part is identical—no more sorting through batches to pick out the “good” ones.
I’ve had customers tell me they thought pressure was just about “getting the material in,” but now they realize it’s about controlling every stage of that process. One customer making silicone keypads for remote controls was having issues with keys that wouldn’t spring back because of uneven density. After switching to our TYM-W LSR Injection Molding Machine, he adjusted the holding pressure to maintain a consistent density across each key, and the springback rate improved from 70% to 99%. That’s a direct result of pressure control making better parts.
What about common mistakes people make? A lot of new operators set the injection pressure super high to “speed up” production, but that backfires. Higher pressure means faster injection, which can cause shear heating—friction as the silicone flows creates heat that makes it cure before it’s done filling. That leads to short shots and parts with hard spots that don’t bend correctly. It’s way better to use the lowest possible injection pressure that still fills the mold, then adjust holding pressure to make up the difference. Smart operators know that slow, controlled pressure beats brute force every time.
And let’s talk about material waste, because that’s a big cost for most molding shops. Every scrap part is money down the drain. If you’re dealing with flash, porosity, or short shots, you’re tossing out expensive silicone material. The right machine’s pressure control cuts down on that waste. Our TYM-W Toggle LSR Injection Molding Machine reduces flash by ensuring uniform clamping pressure, so you don’t have to trim off excess material. For a shop that runs 100,000 parts a month, that adds up to thousands of dollars saved on material alone.
Now, not all machines are created equal. Some budget machines have basic pressure controls that only let you adjust numbers by whole units, not small increments. That’s a problem when you’re working with tiny parts or delicate materials like medical-grade silicone, where even a 5 PSI difference can make or break the part. Our machines, on the other hand, have fine-tuned pressure adjustment—you can tweak it by 1 PSI if you need to, which is perfect for getting those intricate parts right.
I’ve also seen how pressure affects long-term mold life. If you’re running too much injection pressure, that force isn’t just on the silicone—it’s also pushing against the mold itself. Over time, that can cause mold cavities to deform, or wear out the gates faster. Too much clamping pressure can warp the mold plates. That leads to expensive mold repairs or replacements, which no shop wants to deal with. Proper pressure control keeps the forces on the mold within safe limits, extending its life and saving you money in the long run.
So what does this mean for you, as someone working with silicone products? The key takeaway is that pressure isn’t a secondary setting—it’s the core of your molding process. To get high-quality parts, you need precise, consistent pressure control, and that starts with the right machine. Whether you’re working with standard LSR, double-color parts, or delicate medical components, a machine designed for silicone molding (not a generic plastic machine) will give you the pressure accuracy you need.
If you’re tired of dealing with scrap parts, inconsistent quality, or high material waste, it’s worth looking into machines built specifically for silicone. Our TYM-W line is designed with pressure precision at its center—toggle and horizontal models for single-color work, and our 2K double-color machine for multi-material projects. These tools take the guesswork out of pressure, so you can focus on growing your business instead of fixing part defects.
Ready to see how better pressure control can upgrade your silicone product quality? Reach out to us to connect for a consultation and learn more about how our machines fit your production needs.
References
- International Organization for Standardization. (2018). ISO 10993-10: Biological evaluation of medical devices – Part 10: Tests for irritation and delayed-type hypersensitivity.
- Anderson, J. D. (2020). Liquid Silicone Rubber Molding: Process Control and Quality Assurance. Journal of Polymer Processing, 35(2), 112-128.
- Society of Plastics Engineers. (2021). Injection Molding Fundamentals for Thermoset Elastomers. SPE Press.
- Lee, S. H., & Park, J. Y. (2019). Effect of clamping pressure on flash formation in liquid silicone rubber injection molding. Journal of Manufacturing Processes, 41, 205-211.
- British Rubber Manufacturers’ Association. (2022). Best Practices for Silicone Molding Production. BRMA Technical Bulletin.












